The HGV safety inspection checklist, section by section
The periodic safety inspection — the PMI, to most of the trade — is the record an operator keeps between annual tests. Here is what it covers, section by section and the DVSA's way, how the readings are taken, how the interval is kept, and what the operator ends up holding.
Updated 31 October 2026
Workshop in the Republic of Ireland? See Irish prices and sheets →
What the safety inspection is, and what it is not
It is not the annual test. The annual test is the DVSA's — the DVA's in Northern Ireland — and the safety inspection is carried out by the workshop between tests, at an interval the operator sets, and kept as a record. Workbay's is laid out the DVSA's way, and each item is marked satisfactory, defect, rectified or monitor.
Passing it never changes a vehicle's annual test date, which is typed in off the certificate; only a real test moves it.
What the checklist covers
64 items in the sections below, walked in the order the inspection is done: inside the cab, then ground level and under the vehicle, then the tyres, the lamps and markings, the plates and the speed limiter, and the brakes.
| Section | Items |
|---|---|
| Inside the cab | 16 |
| Ground level and under the vehicle | 21 |
| Tyre tread depth | 10 |
| Lamps, reflectors and markings | 8 |
| Plates, limiter and emissions | 5 |
| Brake performance | 4 |
The Service Inspection beside it — 68 items — records what was changed, what was topped up and what was checked, with a section of its own for trailers.
| Section | Items |
|---|---|
| Truck Engine | 24 |
| Trailers | 44 |
Readings, not ticks
Brake performance and tread depth are taken as numbers, and each is judged against the limit held on the sheet. The report prints the reading beside its limit — “0.8 mm (min 1.0)” — so a pass or a fail can be checked afterwards.
| Reading | Limit |
|---|---|
| Service brake efficiency | at least 50% |
| Secondary brake efficiency | at least 25% |
| Parking brake efficiency | at least 16% |
| Brake imbalance across an axle | at most 30% |
| Tread depth, each tyre | at least 1.0 mm |
How often
The interval is the operator's, set out in its maintenance arrangements — commonly somewhere between 4 and 13 weeks, depending on the vehicle's age and work. In Workbay a schedule runs in weeks — every 6 weeks, or every 12 weeks or a distance, whichever comes first — and the next date shows on each vehicle and in the compliance list.
What happens to a defect
- It becomes a defect on the vehicle, with the severity the item carries, the note and up to three photographs or clips.
- It stays open until it is put right; marked rectified, the putting right is recorded against it, so the history shows both.
- The next inspection starts from what the last one found.
- The work goes on the same job — labour on the clock and parts off the shelf — and an estimate can go to the operator by email first.
What the operator ends up holding
The sheet is signed on the screen and stored as a PDF with every finding, the readings and the photographs under the item they belong to — a record you keep. The responsibility for the interval and for what is checked stays with the operator and the inspector who signs it.
- Pass and fail are 60-point targets, sized for gloves at arm's length on a trolley-mounted iPad.
- The whole sheet is on the device; answers, notes, photographs and the signature are sent when signal returns.
- Each vehicle only ever sees the sheets for its type, so a trailer is never asked about its cab.
Fair questions
- Is the safety inspection sheet the one my O-licence needs?
- It is laid out the DVSA's way and covers what a periodic safety inspection covers, marked satisfactory, defect, rectified or monitor. It is a record you keep, signed and stored as a PDF with the defects it raised — the responsibility for the inspection interval and for what is checked stays with the operator and the inspector who signs it.
- Is the safety inspection the same as the annual test?
- No. The annual test is the DVSA's (the DVA's in Northern Ireland); the safety inspection is the workshop's periodic check between tests, and passing it never changes the vehicle's test date.
- How are brake test results recorded?
- As readings: service, secondary and parking brake efficiency and the imbalance across an axle as percentages, each judged against the limit on the sheet and printed beside it on the report.
- Can I print a blank checklist?
- No — the sheet runs in the app, where a fail becomes a defect as it is answered. Each completed inspection becomes a signed PDF report, and the sections and their item counts are listed on this page.
- Does it run without signal?
- Yes. The whole sheet is on the device; answers, notes, photographs and the signature are sent when signal returns, and the report is made once they have.
Keep reading
- HGV workshop software for UK truck & trailer workshops
Truck, lorry and trailer workshops: the safety inspection laid out the DVSA's way, brake and tread readings, PMI intervals in weeks, and operators on account.
- Pre-MOT checklist: what to check, section by section
What a pre-test check covers section by section, what it is not, and how a workshop sells it before the test.
- Offline inspection app for workshops: what to ask
Four questions that tell you what “works offline” really covers, and what still needs a signal.
- The inspection sheets
Every sheet by name, source and item count.
- Pricing
Three plans, a trial with no card.
Next step
Run a real job on it.
7 days is long enough to take a vehicle from booking-in to invoice and judge it on that. No card. Nothing charged unless you add one.